AVX Architect - Event Log Definitions

Table of Contents

Definitions: BMC Faults: IMx8 FAULTS

Definitions:

Fault: Any condition in which the device is not working as intended and the device cannot recover from this condition on its own. A reboot might help the device recover functionality. A service is needed to restore functionality.

Warning: Any condition in which the device is working as intended, but the working parameters are getting close to the limit of failure of the HW. The device can recover from a warning.

BMC Faults:

Fault Name	Notes/Description	Fault Type
I2C1	any error condition(s) detected in peripheral driver	Hardware
I2C2	any error condition(s) detected in peripheral driver
I2C3	any error condition(s) detected in peripheral driver
SPI3	any error condition(s) detected in peripheral driver
SPI5	any error condition(s) detected in peripheral driver
ETH	any error condition(s); link status?
UART	any error condition(s) detected in peripheral driver
FAN0	problem with Fan0
FAN1	problem with Fan1
PS0_12V	1st 12V brick power supply failure
PS1_12V	2nd 12V brick power supply failure
MAIN_5V	Main Board 5V power supply failure
D0_PS	Dante0 card power supply failure
D1_PS	Dante1 card power supply failure
F0_PS	slot0 flag card power supply failure
F1_PS	slot1 flag card power supply failure
F2_PS	slot2 flag card power supply failure
F3_PS	slot3 flag card power supply failure
F4_PS	slot4 flag card power supply failure
F5_PS	slot5 flag card power supply failure
F6_PS	slot6 flag card power supply failure
F7_PS	slot7 flag card power supply failure
IOCTL_20V	Main Board IO control 20V power supply failure
IOCTL_7v5	Main Board IO control 7.5V power supply failure
DC1_5V0	Main Board Dante1 5.0V power supply failure
DC0_5V0	Main Board Dante0 5.0V power supply failure
DC1_3V3	Main Board Dante1 3.3V power supply failure
DC0_3V3	Main Board Dante0 3.3V power supply failure
FLAG67_5V	Main Board flag card slot 6/7 5.0V power supply failure; hw rev0 only
FLAG45_5V	Main Board flag card slot 4/5 5.0V power supply failure; hw rev0 only
FLAG23_5V	Main Board flag card slot 2/3 5.0V power supply failure; hw rev0 only
FLAG01_5V	Main Board flag card slot 0/1 5.0V power supply failure
FLAG234_5V	Main Board flag card slot 2/3/4 5.0V power supply; hw rev1 or later failure
FLAG567_5V	Main Board flag card slot 5/6/7 5.0V power supply; hw rev1 or later failure
FPGA_3V0	Main Board FPGA mixer 3.0V power supply failure
FPGA_1V8	Main Board FPGA mixer 1.8V power supply failure
FPGA_0V95	Main Board FPGA mixer .95V power supply failure
FPGA_0V90	Main Board FPGA mixer .90V power supply failure
BMC_ESW_3V3	Main Board BMC ethernet switch 3.3V power supply failure
PCIE_3V3	Main Board PCIE clock 3.3V power supply failure
UI_PS	display card power supply failure
CLK_FAULT	unable to program clockgen chip
IO_OC	GPIO cards one of the pins is pulling too much current (over current)
EEPROM_F0	No valid BCD image stored
EEPROM_F1	No valid BCD image stored
EEPROM_F2	No valid BCD image stored
EEPROM_F3	No valid BCD image stored
EEPROM_F4	No valid BCD image stored
EEPROM_F5	No valid BCD image stored
EEPROM_F6	No valid BCD image stored
EEPROM_F7	No valid BCD image stored
EEPROM_IOCTL	No valid BCD image stored
EEPROM_DANTE1	No valid BCD image stored
EEPROM_DANTE2	No valid BCD image stored
EEPROM_DISPLAY	No valid BCD image stored
MIXER_LOAD_DEAFULT	Did not load
MUX_LOAD_DEFAULT	Did not load
F0_IMX8_LOAD_DEFAULT	Did not load
F1_IMX8_LOAD_DEFAULT	Did not load
F0_DSP_LOAD_DEFAULT	Did not load
F1_DSP_LOAD_DEFAULT	Did not load
F2_DSP_LOAD_DEFAULT	Did not load
F3_DSP_LOAD_DEFAULT	Did not load
F4_DSP_LOAD_DEFAULT	Did not load
F5_DSP_LOAD_DEFAULT	Did not load
F6_DSP_LOAD_DEFAULT	Did not load
F7_DSP_LOAD_DEFAULT	Did not load
FPGA_DANTE0_LOAD_DEFAULT	Did not load
FPGA_DANTE1_LOAD_DEFAULT	Did not load
SEQUENCER
ETH_SWITCH	unable to configure switch
INRUSH_12V	this could cause the 12V to go down
TCPIP	any error condition(s) detected in tcp/ip stack
IOCTL_NO_CALIB	ioctl doesn't have any or is missing calibration
IOCTL_RELAY	if the ioctl pin is set to relay mode and the voltages exceed 1 V
IOCTL_CH0_VOLT	if the ioctl pin output voltage drops 2 V or more lower than what the target voltage was
IOCTL_CH1_VOLT	if the ioctl pin output voltage drops 2 V or more lower than what the target voltage was
IOCTL_CH2_VOLT	if the ioctl pin output voltage drops 2 V or more lower than what the target voltage was
IOCTL_CH3_VOLT	if the ioctl pin output voltage drops 2 V or more lower than what the target voltage was
IOCTL_CH4_VOLT	if the ioctl pin output voltage drops 2 V or more lower than what the target voltage was
IOCTL_CH5_VOLT	if the ioctl pin output voltage drops 2 V or more lower than what the target voltage was
IOCTL_CH6_VOLT	if the ioctl pin output voltage drops 2 V or more lower than what the target voltage was
IOCTL_CH7_VOLT	if the ioctl pin output voltage drops 2 V or more lower than what the target voltage was
MB_I2C_TEMP0	I2C Nacks
MB_I2C_TEMP1	I2C Nacks
MB_I2C_TEMP2	I2C Nacks
MB_I2C_INR	I2C Nacks
MB_I2C_PCIE0	I2C Nacks
MB_I2C_PCIE1	I2C Nacks
MB_I2C_CLKGEN	I2C Nacks
MB_I2C_EEPROM	I2C Nacks
MB_I2C_BUS_SW	I2C Nacks
MB_I2C_BUS_SW1	I2C Nacks
MB_I2C_BUS_SW2	I2C Nacks
F0_I2C_IO1	I2C Nacks
F0_I2C_IO2	I2C Nacks
F0_I2C_EEPROM	I2C Nacks
F1_I2C_IO1	I2C Nacks
F1_I2C_IO2	I2C Nacks
F1_I2C_EEPROM	I2C Nacks
F2_I2C_IO1	I2C Nacks
F2_I2C_IO2	I2C Nacks
F2_I2C_EEPROM	I2C Nacks
F3_I2C_IO1	I2C Nacks
F3_I2C_IO2	I2C Nacks
F3_I2C_EEPROM	I2C Nacks
F4_I2C_IO1	I2C Nacks
F4_I2C_IO2	I2C Nacks
F4_I2C_EEPROM	I2C Nacks
F5_I2C_IO1	I2C Nacks
F5_I2C_IO2	I2C Nacks
F5_I2C_EEPROM	I2C Nacks
F6_I2C_IO1	I2C Nacks
F6_I2C_IO2	I2C Nacks
F6_I2C_EEPROM	I2C Nacks
F7_I2C_IO1	I2C Nacks
F7_I2C_IO2	I2C Nacks
F7_I2C_EEPROM	I2C Nacks
IO_I2C_IO1	I2C Nacks
IO_I2C_IO2	I2C Nacks
IO_I2C_EEPROM	I2C Nacks
D0_I2C_IO1	I2C Nacks
D0_I2C_EEPROM	I2C Nacks
D1_I2C_IO1	I2C Nacks
D1_I2C_EEPROM	I2C Nacks
UI_I2C_LED_DRVR	I2C Nacks
UI_I2C_EEPROM	I2C Nacks

CPU_UTILIZATION	CPU Utilization more than 90 %
RAM_UTILIZATION	RAM utilization more than 90%
FW_VERSION_MISMATCH	Version not matching to expected firmware version





Warnings

CPU_TEMPERATURE	CPU temperature approaching Threshold
INTERNAL_TEMPERATURE	Internal temperature approaching Threshold

IMx8 FAULTS

ID	Fault Name	Status	HST location	Fault Group	Fault Condition(s)	Fault Clear Condition(s)	Fault Action(s)	Notes/Description
001	SPI_DRIVER			COMM_FAULT	any error condition(s) detected in peripheral driver		XOS msg sent	comm. Error
002	UART_DRIVER			COMM_FAULT	any error condition(s) detected in peripheral driver		XOS msg sent	comm. Error
003	RPMSG			COMM_FAULT	any error returned from rpmsg stack		SCP msg sent to BMC & routed to SDI	comm. Error
004
005
006
007	MCU			MCU_FAULT	heap/stack memory low, etc.		XOS msg sent	not sure about this; its really a warning
008
009
010	MUX			DEVICE_FAULT	invalid response		XOS msg sent
011
012
013
014