Product Name: Enova DGX 100 series enclosures
========== ============ ==================================
FG# Name Description
========== ============ ==================================
FG1061-08 DGX800-ENC Enova DGX 800 Enclosure
FG1061-16 DGX1600-ENC Enova DGX 1600 Enclosure
FG1061-32 DGX3200-ENC Enova DGX 3200 Enclosure
FG1061-64 DGX6400-ENC Enova DGX 6400 Enclosure
========== ============ ==================================
Enova DGX 100 series firmware v3.6.29
========================================================================
* Indicates changes since v3.6.26
- DGX MCPU BootLoader v1.0.8
- DGX MCPU App v3.6.2.1*
- 24p Config v1.2.2.1
- 24p Ext Board v1.0.0.2
- 6p Switch v1.0.2.1
- AIE v1.0.1.4
- Audio App v1.0.0.40
- Audio App (Dante) v1.2.0.4
- Audio BootLoader v1.0.0.4
- Audio BootLoader (Dante) v1.2.0.0
- Audio Input FPGA v1.14
- Audio Output DSP v1.0.0.9
- Audio Output DownMix v1.0.0.2
- Audio Output FPGA v1.14
- Center Board v2.0.6.1
- DGX Power v2.4.2.8
- DGX64 AIE v2.0.1.1
- DVI/HDMI 4K30 In v1.0.3.1*
- DVI/HDMI 4K60 Input v1.0.2.2*
- DVI/HDMI 4K60 Output v1.0.2.1*
- DVI/HDMI Input v1.4.5.1*
- DVI/HDMI Output v1.4.4.1
- DXLink 4K30 Input v1.0.3.1*
- DXLink 4K30 Output v1.0.2.10*
- DXLink Input v1.4.7.1*
- DXLink Output v1.4.5.2*
- SII9396 RX Microcode v1.4.1.1*
- SII9396 TX Microcode v1.3.1.1*
- SRM v1.0.5.1
- Scaler FPGA v1.17
- Valens Rx v3.0.6.0
- Valens Rx SB v3.1.2.0
- Valens Tx v3.0.6.0
- Valens Tx DWP-4K v3.1.2.0
- Valens Tx SB v3.1.2.0
- XG Rx/Tx v1.0.1.4
----------------------------------------------------------
Prerequisites
----------------------------------------------------------
!! Before upgrading to this version please read the KNOWN
ISSUES in regard to AIE extraction on certain outputs.
- NetLinx Studio v4.3.1519 or later.
- NX Series (X200) Master Firmware v1.6.160 or later
Endpoints MUST have the following versions:
- DXLink DX-TX v1.8.38 or later
- DXLink DX-RX v1.13.34 or later
- DXLink DX-RX-4K v2.2.23 or later
- DXLink DXF-TX v1.4.12 or later
- DXLink DXF-RX v1.4.17 or later
- Solecis SDX-X10-DX v1.4.9 or later
- Solecis SDX-X14-DX v2.1.34 or later
----------------------------------------------------------
Features in this release
----------------------------------------------------------
MCPU
- Add date to DGX logtail timestamp
----------------------------------------------------------
Changes in this release
----------------------------------------------------------
MCPU
- Limit ASB AUDOUT_VOLUME (or Level 1 volume) to the specified
AUDOUT_MINVOL and AUDOUT_MAXVOL setting;
- Turn OFF Channel 24 or 25 volume ramp when min/max is reached
- Restore correct serial port baud rate in Load Configuration
- Corrected bogus downmix channel reporting error:
eg. "PreQual: Channel xx signal unsupported for downmix."
- Improved reliability of IO Board reboot recovery
- Corrected pixel clock measurement/reporting issue
HDMI/DVI Input
- Fixed VIDIN_STATUS async notification issue
- Enhanced background checks for processing garbage video
- Fixed cabled connected flag showing inaccurate cable status
- Fixed channel reversal bugs for video format notifications
on DGX6400 inputs 33-64 (VIDIN_RES_REF, VIDIN_HDCPSTATUS)
- Removed shell var "bg_ch_reset" previously in hotfix 3.4.6-1
(Prequal will help block garbage video from sleeping sources)
DXLINK Input
- Fixed channel reversal bug in video format notifications
on DGX6400 inputs 33-64 (VIDIN_RES_REF, VIDIN_HDCPSTATUS)
when using a 4K TX WP
- Corrected HDCP compliance setting persistence when using
a 4K TX WP with a sleeping or disconnected source
- Modify DGX_SHELL>channel command to show freerun res/ref
when no signal present
- Removed shell var "bg_ch_reset" previously in hotfix 3.4.6-1
(Prequal will help block garbage video from sleeping sources)
DXLINK Output
- Improved ethernet switch monitoring to prevent offline
issues with RX on system power up
All 4K30 I/O Boards
- Fixed issue where a source with 2560x1440 format could
cause the I/O boards to reboot if the source was rebooted,
or disconnected
- Added a channl reset for an issue where an invalid format
measurement of some 4k sources (eg. 3840 x 4320i @ 14.9 Hz )
would cause the boards to power off or reboot
- Decrease audio processing delays to minimize unmute time
when audio events are triggered upstream
4K30 HDMI Input
- Fixed issue where certain hotplugs or upstream events could
cause input card to freeze/lock-up
4K60 HDMI Input
- Improved performance for scrambled, premium content
- Correct sporadic mis-reporting of some resolutions
4K60 HDMI Output
- Fixed stale channel command data reported to MCPU
- Fixed WebGUI async Signal Sense status
- Reduced video processing churn with Premium content detection
- Fixed EDID read issue on DVI sinks
----------------------------------------------------------
Known Issues
----------------------------------------------------------
!!IMPORTANT AIE CHANGES!!
- The PreQual feature Pre-Qualifies the video signal AND
the planned route to insure (a) the video is valid and
(b) the output card and sink are capable of handling the
routed signal. An unavoidable side effect of this is
that DXLINK outputs, WITHOUT an endpoint attached, will
be BLOCKED by the switcher (since they can't report their
status). And that means that AIE extraction on an empty
DXLink output is not possible. It is best to use an
empty 2k HDMI output instead for AIE extraction on the
outputs. It is possible to disable the PreQual feature
as a last resort. Contact Tech Support for further
instructions on how to do this.
- The 4K60 I/O boards ONLY work with AIE cards in these
two scenarios:
(a) Extraction FROM the 4K60 INPUT card
(b) Insertion TO the 4K60 OUTPUT card
- DXLINK and DXLINK Fiber Input cards - New cards shipped
with v1.4.6.5 will not work correctly earlier firmware.
DO NOT DOWNGRADE these new cards unless using kit v2.0.6
on a legacy DGX system.
- DGX 100 series systems without 4k60 DXLink should avoid
using v3.6.30. This version can query 2k cards with 4k60
questions leading to various edid errors/warnings. The only
difference between 3.6.29 and 3.6.30 is the MCPU version
of v3.8.0.1. These issues were fixed in DGX kit 3.8.26
and later for mixed or 4k60 only systems.
----------------------------------------------------------
Programming Information
----------------------------------------------------------
- Upgrade time may take up to 2 hours.
- Enova DGX front panels with v2.2.0 provide real time
status of the Enova DGX update when the update starts.
- The Enova DGX Master will provide real time status
of the Enova DGX update. The Master's System -> Devices
page has a "Switcher Update Status" button that will
launch the status update page. This can be accessed at
any time.
- Note: DXLink "RX.c" Receivers are not supported by 4K DXlink
output cards. "RX.e" are supported for non-4K video content.
