Enova DVX 2100 Switcher Device Firmware
Question:
Enova DVX 2100 Switcher Device Firmware
Answer:
Release Notes
DVX-2100HD-SP-T
FG#: FG1905-01 (DVX-2100HD-SP)
FG1905-02 (DVX-2100HD-T)
Current Firmware Version (ColdFire firmware only): v1.4.41
Hotfix Release Date: 06/24/2015
Device ID: 05002: (DVX-2100HD-SP/T Switch)
Prerequisites:
When downloading kit files from NetLinx Studio:
- Upgrading DVX device firmware (usually device 5002):
a. use kit file SW1905_DVX_KIT_DVX_2100HD_SP_T_v1_4_36.kit
Within the "Send to NetLinx Device" dialog box please check the "Reboot
Device" check box before proceeding with KIT file download.
b. Starting with the release of V3_51_359, DVX utilizes an intelligent
download feature that will skip any part of the DVX device firmware that
has the same version as the firmware already loaded in the system. For
example, the FGPA portion of the firmware will be skipped if there are
no changes to it in the new release being uploaded. This in enabled by
default. While it should not be necessary, the user can change the
intelligent downloading settings by using the following telnet command in
superuser mode:
smart-downloading [enable|disable|status]
- **Set Video/Audio to Default NEEDED if previous version is old than
V3_51_364**. Set the Video setting to factory default after successfully
completing the firmware downloads.
a. Record all current audio and video configuration settings, as the
next steps will overwrite them.
b. Using the front panel press the "VIDEO MENU" button.
c. Navigate to "Revert to Default:NO" using the up arrow key.
d. When at the "Revert to Default:NO" menu item press the right arrow
key once.
e. When asked "Are you Sure?" at the front panel, press the right
arrow key to reset to factory Video defaults. The front panel will
report back with "Defaulting Video"
f. Using the front panel press the "AUDIO MENU" button, then go through
similar steps b,c and d to reset to factory Audio defaults.
g. Reset the audio and video configuration settings to those recorded
in step a.
Changes in this release
-----------------------
-- New Fixes:
-- Added ACK/NAK processes for sending and receiving messages with the master.
This will allow us to be able to detect and resend corrupted messages
- Accumulated Fixes from previous Hotfixes
- v1.4.33
-- Fixed VIDOUT_ON-ENABLE/DISABLE to enable and disable video on the correct
output port.
-- Switching audio inputs with global mute on and a microphone input enabled
will now keep audio muted through the switch.
- v1.4.32
-- Fixed issue where switching from a high-resolution DVI input to an input
with nothing connected would leave a frozen image.
-- Modified the operation of input gain mute (channel 143) such that changes
to the associated gain level do not cause it to unmute.
-- Corrected an issue where the gain mute setting was not being retained for
each input when switching audio.
-- Fixed an issue where values sent to LEVEL 1 were being returned 2-3 units
lower.
-- Added the resolution 1280x800@60Hz to the default EDID table sent to
connected VGA/DVI sources.
- v1.4.29
-- Reduced amount of dropped ICSP messages by increasing size of internal
message queue
-- Fixes issues regarding gain mute (channel 143) unmuting and not handling
multiple inputs
- v1.4.21
-- Improved VIDOUT_ON/OFF feature where DVX works in consistant way during
source switching mode and test pattern mode.
- v1.4.20
-- Fixed issues where HUE,Saturatioin values were not updated in web
interface if that source was unselected(inactive).
-- Fixed issue where DVX send_command
¡®FP_LOCKOUT-ENABLE¡¯ w/ ¡®FP_LOCKTYPE-2
w/ FP access appears to stop NetLinx execution.
-- Fixed issue where DVX send_command 'VIDOUT_ON/OFF" worked with incorrect
output port.
-- Re-enabled the level 36 & 37 for EQ band 6 & 7.
- v1.4.36
-- Fixed issue where the switch would appear to accept a message from the
NI controller yet would not perform the task. This was due improper
handling of an internal exception which caused the video task to hang.