This document lists the default user name and passwords for various AMX products. Directions on how to return to factory default settings are also included where available.
The information in this article applies to:
Currently supported AMX products
Camera Controllers
PTE-300
Default IP Address: 192.168.1.160
Default Baud Rate: 9600,N,8,1
Central Controllers
NI Series
Default Administrator User Name: administrator
Default Administrator Password: password
Default User Name: NetLinx
Default Password: password
Reset to Factory Defaults:
See NetLinx Studio or the Master Configuration Manager webpages
Digital Signage
IS-PLAYER-200
Default IP Address: DHCP (zero-config)
IS-SPX-1000
Default IP Address: DHCP (zero-config)
Default User Name: <none>
Default Password: <none>
Reset to Factory Defaults:
1. Unplug the unit from the power.
2. Push the reset button and keep it pressed.
3. Power up the IS-SPX-1000 unit.
4. Wait with the reset button pressed for at least 8 seconds. 5. Release the reset button.
IS-XPT-2000
Default IP Address: DHCP (zero-config)
Endeleo UDM-0102
Default IP Address: 192.168.0.96
Default User Name: <leave blank>
Default Password: admin
Default Baud Rate: 9600,N,8,1 No Flow Control UDM-0404
Default IP Address: 192.168.0.96
Default User Name: <leave blank>
Default Password: admin
Default Baud Rate: 9600,N,8,1, No Flow Control UDM-0808-SIG
Default IP Address: DHCP (zero-config)
Default User Name: administrator
Default Password: password
Reset to Factory Defaults:
Use the 'RESETFACTORY' command or Use the WebConsole's Security Settings tab UDM-1604(B)
Default IP Address: 192.168.0.96
Default User Name: <leave blank>
Default Password: admin
Default Baud Rate: 9600,N,8,1, No Flow Control
Reset to Factory Defaults:
Use the 'Hub Reset' option in the Configuration Webpages, then cycle power UDM-1604C
Default IP Address: 192.168.0.96
Default User Name: <leave blank>
Default Password: admin
Default Serial Port: 9600, N, 8, 1, No Flow Control
Reset to Factory Defaults: Use the 'Reset Hub' option in the Configuration Webpages, then cycle power
Environmental Controls
ENV-VST-C
Default Password: 1988
Restore to Factory Defaults:
Use the 'ZAP!' command ViewStat
Default Password: 7777
Network/Communication
CSG (Communications Gateway)
Default IP Address: 192.168.69.1
Default User Name: admin
Default Password: 1988
Reset to Factory Defaults:
Use the 'Factory Reset' tab in the web pages or press the Reset Switch on the rear panel continuously during the boot process. MET-ECOM/-D
Default IP Address: DHCP (zero-config)
Default User Name: Admin
Default Password: 1988
Reset to Factory Defaults:
Push and hold the ID/Reset pushbutton on the rear panel for at least 10 seconds.
NXA-ENET8POE
Default IP Address: 192.168.2.10
Default User Name: admin
Default Password: 1988
Reset to Factory Defaults:
1. Remove the power cord from the back of the device.
2. Remove all cables from the front-panel ports.
3. Connect port 1 to port 2 on the front panel, using a standard network cable.
4. Reconnect the power cord to the rear of the switch.
5. The PoE LEDs (FIG. 1) will flash on and off at least two times, followed by the ƒn Link/ACT LEDs. Do not disconnect the cable or the power cord until only the first two Link/ACT LEDs are a steady green and the others are off.
6. Disconnect the power cord and THEN disconnect the network cable.
7. Reconnect the power cord. The NXA-ENET8POE is now reset to its factory defaults.
NXA-ENET24
Default IP Address: DHCP
Default Privileged User Name: Admin
Default Privileged Password: 1988
Default Normal Exec User Name: guest
Default Normal Exec Password: guest
Reset to Factory Defaults:
The switch's system defaults are provided in the configuration file “Factory_Default_Config.cfg." To reset the switch defaults, this file should be set as the startup configuration file.
NXA-WAP200G
Default IP Address: 192.168.1.240
Default User Name: Admin
Default Password: 1988
Reset to Factory Defaults:
Press the Reset button on the rear panel for 10 seconds
NXA-WAP250G
Default IP Address: 192.168.1.240
Default User Name: Admin
Default Password: 1988
Reset to Factory Defaults:
Hold down the reset button on the bottom panel for 10 seconds or more, any configuration changes you may have made are removed, and the factory default configuration is restored to the access point.
NXA-WAP1000
Default IP Address: 192.168.0.1
Default User Name: admin
Default Password: 1988
Reset to Factory Defaults:
Pressing and holding the Hard Reset button on the rear panel for six seconds resets the unit to factory default settings.
NXA-WAPZD1000 (Zone Director)
Default IP Address: DHCP/ 192.168.0.2
Note: The NXA-WAPZD1000 is shipped with its default IP address settings as "DHCP", but if it is installed outside of a DHCP network, the device will revert to the default IP address (192.168.0.2).
Default Console Port Settings: 115200, N, 8, 1
Default User Name: admin
Default Password: admin
Reset to Factory Defaults:
Press and hold the Reset button for 8 seconds. The Status LED will now start flashing green to denote its default status.
NXB-KNX (KNX Gateway)
Default IP Address: DHCP
Note: The NXB-KNX is shipped with its default IP address settings as "DHCP", but it features a built-in zero-configuration networking client that allows you to determine the unit's IP address via NetLinx Studio v3.0 (or higher), or a similar zero-configuration client.
Security is disabled by default, but if enabled, the following are is default login
Default User Name: administrator
Default Password: password
Reset to Factory Defaults: is accomplished only in the web interface.
NXR-ZGW/-ZRP
Default IP Address: 192.168.1.140
Default User Name: Admin
Default Password: 1988
Reset to Factory Defaults:
Press and hold the ID Button for approximately 30 seconds to return the NXR-ZGW to factory default settings.
NXR-ZGW-PRO/-ZRP-PRO
Default IP Address: DHCP/169.254.1.2
Note: The NXR-ZGW-PRO is shipped with its default IP address settings as "DHCP", but if it is installed outside of a DHCP network, the device will revert to the default IP address (169.254.1.2).
Default User Name: Admin
Default Password: 1988
Reset to Factory Defaults:
Press and hold the ID Button for approximately 30 seconds to return unit to factory default settings.
Television Distribution System
DTV-TX Transmitter
Default IP Address: DHCP
Reset to Factory Defaults:
In the Configuration Manager, Click to reset the Network Settings for selected Transmitter to DHCP.
DTV-RX Receiver
Default IP Address: DHCP
TVM-1600
Default IP Address: 192.168.0.96
Default User Name: <leave blank>
Default Password: admin
Video Management/Distribution
MAX Server
Default IP Address: 192.168.1.30
Default User Name: root
Default Password: Mozart
MAX-CSD10
Default IP Address: DHCP
Default User Name: administrator (Web Interface)
Default Password: password (Web Interface)
Reset to Factory Defaults:
Press and hold the ID button on the front panel for 10 seconds to reset the parameters and reboot the MAX unit.
MAX-CSE
Default IP Address: DHCP
Default User Name: administrator (Web Interface)
Default Password: password (Web Interface)
Reset to Factory Defaults:
Press and hold the ID button on the front panel for 10 seconds to reset the parameters and reboot the MAX unit.
V2 Server
Default IP Address: DHCP
Note: (use 'ping V2AMX-<SVCTAG>' to find IP address. <SVCTAG> is the service name, which you can find on the front of your server.
Default User Name: Administrator
Default Password: vision2
