Martin MAC Fixture Display Warning Messages Explained

Technical Support Guide

Brand:

Martin

Models:

Martin MAC series of fixtures

How and when is a Warning message displayed:

Warning messages notify the user when the fixture is approaching a condition that may cause problems or when special attention is required during operation or service.

Warning codes remain on the display until the condition is cleared.

If multiple warnings are present, each is shown for 3 seconds in sequence, then the cycle repeats.

If the display is inactive, warnings are not shown; the orange blinking LED indicates a warning.

Heading 1:

Name	Short Code: [3 characters]	Medium Code: [4 characters]	Long Code: [16 characters]	Descriptive message [ LCD display ]	LED indicator	RDM status ID code	Description
Lamp life	LTI	LTIM	LAMP LIFETIME	Lamp lifetime	Orange blinking	0x8000	Lamp has less than 10% of it expected lifetime left.
Door open		DOOR	LAMP DOOR OPEN	Lamp door open	Orange blinking	0x8001	Lamp door is open and it is not possible to strike the lamp.
Hot lamp	HOT	HOT	LAMP HOT	The Lamp is HOT Remaining time XX min	Orange blinking	0x8002	Shown when lamp has been struck but didn’t come on. Lamp is hot and it is not possible to turn it on (non hot restrike fixtures only!).
EEprom warning		EEPR	EEPROM INVALID	EEprom invalid/No conn	Orange blinking	0x8007	EEprom communication failed contact Martin Support.
Bank warning		BANK	BANK NO ACCESS	Unable to unpack bank	Orange blinking	0x8008	Bank has been copied to fixture but not able to unpack it.
Air filter warning		AIRS	CHECK AIRFILTERS	Air filter needs service	Orange blinking	0x8009	Air filter timer has timed out.
Dimmer warning		DINA	DIMMER ADJUST	Dimmer not adjusted	Orange blinking	0x800A	No dimmer adjustment data in EEprom.
Shutter warning		SHNA	SHUTTER ADJUST	Shutter not adjusted	Orange blinking	0x800B	No shutter adjustment data in EEprom.
Pan warning		PANA	PAN ADJUST	Pan not adjusted	Orange blinking	0x800C	No Pan adjustment data in EEprom.
Tilt warning		TINA	TILT ADJUST	Tilt not adjusted	Orange blinking	0x800D	No Tilt adjustment data in EEprom.
USB warning		FUSB	USB UPLOAD	Forced USB upload enable	Orange blinking	0x800E	The fixture was started in forced upload mode (esc held during power up).
Battery warning		BATM	BATTERY MODE	Battery mode	Orange blinking	0x800F	Changed to battery power source.
Pan temperature warning		GxyM	GOBO x–y MISSING	Gobo wheel x Gobo y missing	Orange blinking	0x8010 – 0x80FF	Gobo y on gobowheel x was not seen during reset. If all gobos on a gobowheel is not seen, a RxER will also be set.
Mains warning		MALW	MAINS LOW	Mains low	Orange blinking	0x8100	Mains voltage is below acceptable level, lamp may not be able to strike.
Upload mode	UPL	UPL	UPLOAD MODE	Upload mode	Orange blinking	0x8101	Shown in display if fixture is in upload mode.
Invalid License Key		INLK	INVALID LICENSE KEY	Invalid License Key	Orange blinking	0x8102	Shown for 5 seconds when invalid license key is entered
Decrypting License Key		DELK	DECRYPTING LICENSE KEY	Decrypting License Key	Orange blinking	0x8103	Shown as long license key is decrypted.
CMY PCB temperature warning		CMTW	CMY TEMP HIGH	CMY PCB temp too high	Orange blinking	0x8104	CMY PCB temperature sensor continuously measures a temperature above normal operating temperature
Effect PCB temperature warning		EFTW	EFF TEMP HIGH	Effect PCB temp too high	Orange blinking	0x8105	Effect PCB temperature sensor continuously measures a temperature above normal operating temperature
Zoom focus PCB temperature warning		ZFTW	ZF TEMP HIGH	Zoom focus PCB temp too high	Orange blinking	0x8106	Zoom focus PCB temperature sensor continuously measures a temperature above normal operating temperature
Pan tilt PCB temperature warning		PTTW	PT TEMP HIGH	Pan tilt PCB temp too high	Orange blinking	0x8107	Pan tilt PCB temperature sensor continuously measures a temperature above normal operating temperature
UI PCB temperature warning		UITW	UI TEMP HIGH	UI PCB temp too high	Orange blinking	0x8108	UI PCB temperature sensor continuously measures a temperature above normal operating temperature
PSU PCB temperature warning		PUTW	PSU TEMP HIGH	PSU PCB temp too high	Orange blinking	0x8109	PSU PCB temperature sensor continuously measures a temperature above normal operating temperature
BAL PCB temperature warning		BATW	BAL TEMP HIGH	Ballast PCB temp too high	Orange blinking	0x810A	Ballast PCB temperature sensor continuously measures a temperature above normal operating temperature
Frost not adjusted warning		FTNA		Frost not adjusted	Orange blinking	0x810B	No frost adjustment data in EEprom.
New firmware required warning		FW	NEW FW REQUIRED	New Firmware required	Orange blinking	0x810C	Fixture requests upload of new firmware
Barndoor not adjusted warning		BDNA		BARNDOOR NOT ADJUSTED	Orange blinking	0x810D	No barndoor adjustment data in EEprom.
Service mode warning		SERV	SERVICE MODE	Service mode enabled	Orange blinking	0x810E	Fixture is in service mode.
Safety loop warning		SL W	SAFETY LOOP	Safety loop error occurred	Orange blinking	0x810F	A safety loop error occurred, but is no longer active. Warning is cleared on power off.
Framing not adjusted warning		FRNA		FRAMING NOT ADJUSTED	Orange blinking	0x8110	No framing adjustment data in EEprom.
Wash Effect not adjusted warning		WENA		Wash Effect not adjusted	Orange blinking	0x8111	No Wash adjustment data in EEprom
Quadray not adjusted warning		QRNA		QUADRAY NOT ADJUSTED	Orange blinking	0x8112	No Quadray adjustment data in EEprom.
LED driver temperature warning		LDTW	LED DRV TMP HIGH		Orange blinking	0x8113	The LED driver PCB temperature sensor continuously measures a temperature above normal operating temperature
BEAM pixel board temperature warning		BETW	BEAM TMP HIGH		Orange blinking	0x8114	The Beam LED PCB temperature sensor continuously measures a temperature above normal operating temperature
AURA pixel board temperature warning		AUTW	AURA TMP HIGH		Orange blinking	0x8115	The Aura LED PCB temperature sensor continuously measures a temperature above normal operating temperature
PFC temperature warning		PFTW	PFC TMP HIGH		Orange blinking	0x8116	The PFC PCB temperature sensor continuously measures a temperature above normal operating temperature
DC/DC temperature warning		DCTW	DC TMP HIGH		Orange blinking	0x8117	The DC-DC PCB temperature sensor continuously measures a temperature above normal operating temperature
Quadray temperature warning		QRTW	QR TMP HIGH		Orange blinking	0x8118	The Quadray PCB temperature sensor continuously measures a temperature above normal operating temperature
Beam twist not adjusted		BTNA	BEAMTWIST ADJUST		Orange blinking	0x811A	Beam twister lens not adjusted
Fan warning		FAN	LAMP R FAN		Orange blinking	0x811B	Fan has been steadily underperforming by X RPM for Y seconds
Fan warning		FAN	LAMP L FAN		Orange blinking	0x811C	Fan has been steadily underperforming by X RPM for Y seconds
Framing board temperature warning		FRTW	FRAMING TMP HIGH		Orange blinking	0x811D	Framing PCB temperature sensor continuously measures a temperature above normal operating temperature
IBD board temperature waring		IBTW	IBD TMP HIGH		Orange blinking	0x811E	IBD PCB temperature sensor continuously measures a temperature above normal operating temperature
Current Driver temperature warning		CCTW	CC DRIVER TEMP HIGH		Orange blinking	0x811F	The Constant currant driver PCB temperature sensor continuously measures a temperature above normal operating temperature
Pan temperature warning		PNTW	PAN TEMP HIGH		Orange blinking	0x8120	Pan driver PCB temperature sensor continuously measures a temperature above normal operating temperature
Tilt temperature warning		TLTW	TILT TEMP HIGH		Orange blinking	0x8121	Tilt driver PCB temperature sensor continuously measures a temperature above normal operating temperature
Framing 2 not adjusted warning		F2NA	FRAMING2 ADJUST		Orange blinking	0x8122	Framing not adjusted
Framing 2 board temperature warning		F2TW	FRAMING2 TMP HIGH		Orange blinking	0x8123	Framing 2 driver PCB temperature sensor continuously measures a temperature above normal operating temperature
LED board temperature warning		LETW	LED BOARD TEMP HIGH		Orange blinking	0x8124	LED PCB temperature sensor continuously measures a temperature above normal operating temperature
LED board EEPROM		LEEP	LED BOARD EEPROM		Orange blinking	0x8125	LED Board EEPROM device not mounted or connection has failed
Wet too long		WTTL	WET TOO LONG		Orange blinking	0x8126	Fixture has been wet for an extended period. To remove the warning, a complete dry-off procedure is required
Drying out		DRYO	DRYING OUT		Orange blinking	0x8127	Drying off function activated
Empty water needed		NEMW	NEED EMPTY WATER		Orange blinking	0x8128	Water buildup in front of head. Draining required
Emptying water		EMPW	EMPTYING WATER		Orange blinking	0x8129	Fixture draining water from front of head
Connectors facing upwards		CTUP	CONNECTORS UPWARD		Orange blinking	0x812A	Fixture base is installed with connectors facing upward, where there is a risk of water accumulation in case of rain
Serial Number Mismatch		SRNM	SR NO MISMATCH		Orange blinking	0x812B	CMY module, Light Engine or Main board may have different serial numbers.
Dry out function recommended		DRYR	DRY OUT FUNC RECOM		Orange blinking	0x812E	Product has detected it has been wet and needs drying out.
NFC Warning		NFCW	NFC WARNING		Orange blinking	0x812F	NFC communication works, but we are unable to initialize the data in the tag
Safe Parking warning		PARK	SAFE PARKING		Orange blinking	0x8130	Safe parking to avoid sun damage / rain buildup in head.
Animation wheel rotate warning		AWRM	AW ROT MISSING		Orange blinking	0x8131	Animation wheel rotation not indexing
Air temperature high		AITW	AIR TEMP HIGH		Orange blinking	0x8132	Air temp high
Air humidity high		AIHW	AIR HUMIDITY HIGH		Orange blinking	0x8133	Air humidity high
No Dimming Zones defined		DMZQ	NO DIMMING ZONES		Orange blinking	0x8134	No Allowed Dimming Zones enabled

[Add any additional info here]